论文部分内容阅读
温轧温度对Cr-Ti-B系低碳钢组织与织构的影响
【出 处】
：
材料研究学报
【发表日期】
：
0年期
其他文献
Effects of surface roughness on interracial dynamic recrystallization and mechanical properties of T
The influence of surface roughness on the interfacial dynamic recrystallization kinetics and mechanical properties of Ti-6Al-3Nb-2Zr-1Mo hot-compression bonding joints was systematically investigated.It is found that for the bonding interface of rough sur
Sc solute clusters with a high number density were produced in an Al-0.3 wt.％Sc alloy when aged at 250 ℃,while fine Al3Sc precipitates were predominantly formed in the same alloy aged at 300 ℃.The alloy strengthened by Sc solute clusters displayed higher
用固相反应法制备(Gd1-xEr)2(Zr0.8Ti0.2)2O7(摩尔分数x=0,0.2,0.4)陶瓷并测试其晶体结构、显微形貌和物理性能,研究了Er2O3掺杂的影响.结果 表明,(Gd1-xErx)2(Zr0.8Ti0.2)2O7陶瓷具有立方烧绿石结构,显微结构致密,在室温至1200℃高温相的稳定性良好;Er3+掺杂降低了陶瓷材料的热导率和平均热膨胀系数,当x=0.2时,其1000℃的热导率最低(为1.26 W·m-1 ·k-1).同时,Er3+掺杂还提高了这种材料的硬度和断裂韧性.
Effect of thermal ageing and dissolved gas on corrosion of 308L stainless steel weld metal in simula
The corrosion of unaged and 7000-h thermally aged 308L stainless steel weld metals in simulated PWR primary water under aerated and deaerated conditions was investigated,involving the corrosion of austenite,δ-ferrite and δ-ferrite/austenite phase boundary
将棉织物浸入多巴胺、硝酸银、十六烷基三甲氧基硅烷的乙醇溶液中,取出烘干制备出超疏水棉织物.用扫描电子显微镜和X射线光电子能谱表征其表面形貌和元素,用接触角测量仪测量其接触角并进行摩擦或液体浸泡(如酸、碱、沸水)实验检测其耐用性.结果 表明,聚多巴胺的强附着性使原位生成的银纳米粒子能经受摩擦或不同液体的浸泡,从而使超疏水织物具有良好的耐用性.超疏水棉织物还具有良好的油水分离性能,其油水分离效率高达97％,油流量最高可达15.93 m3·m-2·h-1.
A new approach for determining GND and SSD densities based on indentation size effect:An application
Dislocation plays a crucial role in controlling the strength and plasticity of bulk materials.However,de-termining the densities of geometrically necessary dislocations (GNDs) and statistically stored disloca-tions (SSDs) is one of the classical problems
Urea-assisted hydrothermal synthesis of MnMoO4/MnCO3 hybrid electrochemical electrode and fabricatio
Transition metal molybdates/carbonates and hybrid nanomaterials have attracted great attention in en-ergy storage applications because of their enriched redox activity,good electronic conductivity,and sta-ble crystallinity.We synthesize a multicomponent M
采用OM和SEM研究了奥氏体化温度对HSLA钢组织演变和低温韧性的影响.结果 表明:奥氏体化温度由850℃升高至950℃(实验钢的AC3温度为819℃)并保温30 min后,奥氏体的平均晶粒尺寸由7.22 μm增大到17.39 μm,在850～950℃淬火后的显微组织均为板条马氏体,屈服强度和抗拉强度均呈下降趋势,延伸率没有明显的变化,但是-20℃下的冲击韧性由97 J显著降低到31J.使用EBSD和ARPGE软件的晶体学分析结果表明,随着奥氏体化温度的升高晶粒尺寸增大且变体选择增强,表现为奥氏体晶粒大部
将Mg-1A1-0.4Ca-0.5Mn-0.2Zn(质量分数,％)合金在不同温度挤压,研究其微观组织和力学性能.结果 表明:在260℃和290℃挤压的合金均发生不完全动态再结晶,再结晶晶粒尺寸分别为0.75 μm和1.2 μm.二者均具有高密度的G.P.区和球状纳米析出相,能抑制位错运动并为动态再结晶提供丰富的形核位点.沿晶界析出的纳米相能抑制晶界的运动和限制再结晶晶粒的生长,从而生成尺寸为0.75 μm的超细晶粒.随着挤压温度从260℃提高到290℃,合金的屈服强度从322 MPa提高到343 MPa,
分别使用反应溅射Al+α-Al2O3(15％ α-Al2O3,质量分数)复合靶和在金箔基体表面预植α-Al2O3籽晶,促进α-Al2O3薄膜的低温沉积.使用扫描电子显微镜(SEM)、掠入射X射线衍射(GIXRD)和能谱仪(EDS)等方法表征薄膜样品的表面形貌、相结构和元素组成.结果 表明,在射频反应溅射Al+α-Al2O3复合靶、沉积温度为560℃条件下能在Si(100)基体上沉积出化学计量比的单相α-Al2O3薄膜;使用射频反应溅射A1靶、沉积温度为500℃条件下能在预植α-Al2O3籽晶(籽晶密度为1