1988年的中国经济:成就·困难·希望

来源 :财贸经济 | 被引量 : 0次 | 上传用户:liongliong463
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
1988年,我国国民经济继续向前发展,国家经济实力进一步增强;同时,国民经济中的供求矛盾、结构性矛盾加剧,通货膨胀,物价猛增。复杂而严峻的客观形势向我们提出了新的挑战,也提供了新的机会,孕育着新的希望。如何根据1988年9月党的十三届三中全会确定的治理经济环境、整顿经济秩序、全面深化改革的方针,总结经验,全面调整,共渡难关,把社会主义经济的发展和改革引上健康发展的大道,是全国上下面临的重大而艰难的任务。 In 1988, the national economy of our country continued to move forward and the economic strength of the country was further enhanced. At the same time, the contradiction between supply and demand, structural contradictions in the national economy intensified, and inflation and prices soared. The complicated and harsh objective situation presents us with new challenges, provides new opportunities and gives birth to new hope. How to rectify the economic order, comprehensively deepen the principle of reform, sum up experience, comprehensively adjust and tide over the difficulties, and lead the development and reform of the socialist economy to a healthy state according to the economic conditions set in the Third Plenary Session of the 13th CPC Central Committee in September 1988 The road to development is a major and difficult task all over the country.
其他文献
一、引言应用佛切迈尔(Fercheimar)方程测定微孔金属材料流体渗透性的方法,在70年代,得到国际上许多国家的普遍承认。与应用达西(Darcy)公式测定微孔金属流体渗透性的方法相
Lung lymph fistula preparation was used to study the effectsof hypoxia and endotoxin on pulmonary pressor response andpulmonary fluid exchange in 9 conscious g
铸造铝合金的变质处理是生产中广泛采用的工艺过程。目前工业上采用的变质剂以Na为主,但是这在工艺上存在着一系列至今无法克服的缺点,如变质有效期短,具有腐蚀性等等。因此
一、问题的提出 1986年我厂冷轧车间用外厂供应的宽1060毫米、厚7.3毫米铸轧铝板坯冷轧加工成厚1.5毫米至0.8毫米的卷材和片材。在冷轧成品的表面存在程度不一的下列块陷:1
30CrMnMoTiA钢是立足于我国资源、为代用30CrNi3A、25CrNiWA等含镍钢而研制的新钢种。它具有低的过热敏感性、较好的淬透性、抗回火性和较小的回火脆化倾向,经淬火、低温回
近年来,国外焊接车间的生产技术有了较大的进展,主要表现在电子计算机的普遍推广、先进技术的开发和应用以及高效设备的研制等方面。本文以重机厂、化工炼油设备厂等为重点,
1 应用范围 本标准规定一种用于测量金属涂层厚度的阳极溶蚀的电量测定法。 表1给出可以采用这种方法检验的涂层与基层的典型组合,其它的组合可采用现有的电解质(见补充件B)
一、前言作为金属着色的技术,已有许多种方法,如金属铝及其合金的各种着色。不锈钢(铁)的各种着色。但是,这些方法受到材料、成本以及色彩鲜艳程度等方面的限制,所以应用面
一、前言 国内外专家研究冲裁机理,都重视冲裁间隙这个重要参数。实践证明,间隙值对工件的断面质量、尺寸精度、模具寿命等均起主要影响,但是,从质量、精度、寿命等不 Firs
一、前言退火后冷轧薄板的综合性能主要取决于退火工序,而退火工艺制度的制定,则主要是退火温度和保温时间的选择。当然,加热速度和冷却速度在一定的条件下也会影响钢板的性