【摘 要】
：
Inconel 738 LC samples were fabricated using laser powder bed fusion under continuous-wave and pulsed-wave modes.Microstructure,surface quality and mechanical properties were compared to eval-uate the printing quality between these 2 laser beam modes.The
【机 构】
：
Department of Mechanical and Energy Engineering,Southern University of Science and Technology,Shenzh
论文部分内容阅读
Inconel 738 LC samples were fabricated using laser powder bed fusion under continuous-wave and pulsed-wave modes.Microstructure,surface quality and mechanical properties were compared to eval-uate the printing quality between these 2 laser beam modes.The results show that the application of pulsed wave could effectively eliminate cracking in the as-fabricated sample,despite 0.046％ porosity generated.Further microstructure analysis revealed that the refinement of grains by the pulsed-wave laser beam was the main contributor in eliminating the cracks.And this refinement was ascribed to the higher cooling rate under the discontinuous radiation of laser beam proofed by the numerical simulation.And the pore formation was related to Rayleigh instability and residual bubbles in the sample under the pulsed-wave mode,while pores were less detrimental to the mechanical properties than cracks.There-fore,the part under the pulsed-wave mode exhibited superior mechanical performance compared to that under the continuous-wave mode.
其他文献
Graphene oxide (GO),a new and promising material,has been widely used as a co-catalyst in photocat-alytic reactions;however,its capacity as a sole photocatalyst has rarely been investigated.In this study,ultraviolet (UV) light irradiation was used as a mo
由于盐湖地区的产业发展对交通基础设施提出了更高的要求,环境变化使得盐湖地区的盐岩卤水路基病害多发。为解决这些关键问题,本文提出使用石灰和粉煤灰等无机结合料提高盐岩的力学强度和抗溶蚀性能,形成石灰粉煤灰稳定盐岩混合料作为路面基层材料。本文在研究过程中采用有约束的配方均匀设计方法,在较大取值范围内得出了石灰与粉煤灰掺量变化与混合料7d无侧限抗压强度、温缩系数和干缩系数的回归关系,回归结果表明,合理剂量
MCrAlY (M=Ni,Co,NiCo) alloys have been widely used as a bond layer for thermal barrier coatings (TBCs).However,oxides form discontinuously on MCrAlY surface in the marine environment since Cr2O3 can react with NaCl and H2O at temperatures above 500 ℃.Repl
Lightweight and high-performance are two determining factors for metal-organic-frameworks (MOFs)derived microwave absorbers.However,most of the reported MOFs derived absorbers usually pos-sess high filler loading.Herein,a series of MOFs derived magnetic p
The shuttle effect of lithium polysulfides (LiPSs) and sluggish redox conversion significantly hinder prac-tical implementation of lithium-sulfur batteries (LSBs).To overcome these issues,herein,we present MoP quantum dots anchored N,P-doped graphene (MPQ
In this study,MgAl-V2O74-LDHs/(poly(ethyleneimine)(PEI)/MXene)n composite films were synthesized via(i) in-situ hydrothermal growth of Mg-Al layered double hydroxides (LDHs) on AZ31 alloy followed by vanadate intercalation reactions,and (ii) the as-prepar
近些年由于国民经济的需求增加,对矿产资源的开发力度也随之加大,我国浅部各类资源已急剧减少,对于矿体的寻找也逐步向深部矿、隐伏矿发展。目前,中国在成矿理论、深部探测研究等方面都取得了新进展,同时也研制了一批不同种类的地质勘探仪器装备,并在实际应用中取得了显著效果,在之前的地质勘查分析方法基础上进行了革新,完善了多种勘探技术体系。而电磁方法也越来越广泛的应用于各类资源的勘探中。地空瞬变电磁法作为一种重
In this work,through the self-developed setup for in situ electrochemical tests,the corrosion behavior of 13Cr stainless steel under the combined effect of stress and crevice in high pressure CO2/O2 environment was investigated.The results show that 13Cr
A nanoscale observation utilizing the transmission electron microscopy (TEM) device was presented to investigate the hot deformation behavior of[β-solidifying γ-TiAl alloy (Ti-42.9Al-4.6Nb-2Cr,at.％) with duplex structure,and elucidate twinning and twin in
We have for the first time elucidated the microstructural evolution and deformation behaviors of a gra-dient textured AZ31B Mg alloy plate under the ultrahigh strain rate of-106 s-1 that is generated by a two-stage light gas gun with the hypervelocities o