【摘 要】
：
T23 steel (2.25Cr-1Mo-1.6W-0.24V-0.05Nb,in wt.％) has been widely used as water walls in ultra-supercritical (USC)power plants.However,high reheat cracking susceptibility of T23 steel hazarded the safety of USC power plants.It is aimed to improve the rehea
【机 构】
：
State Key Laboratory of Advanced Special Steel and Shanghai Key Laboratory of Advanced Ferrometallur
论文部分内容阅读
T23 steel (2.25Cr-1Mo-1.6W-0.24V-0.05Nb,in wt.％) has been widely used as water walls in ultra-supercritical (USC)power plants.However,high reheat cracking susceptibility of T23 steel hazarded the safety of USC power plants.It is aimed to improve the reheat cracking susceptibility of T23 steel from the perspective of modifying chemical composition.Gleeble-3800 thermal simulator was used to simulate the coarse-grained heat-affected zone (CGHAZ) in T23 and modified T23 steels via thermal simulation of welding,and then evaluate the reheat cracking susceptibility in CGHAZ of T23 and modified T23 steels by the isothermal slow strain rate tensile test.The microstructure was systematically investigated by optical microscopy,scanning electron microscopy and transmission electron microscopy.The results show that the reheat cracking susceptibility of modified T23 steel is extremely improved.Compared with T23 steel,there are fewer M23C6 particles at the grain boundaries in modified T23 steel,and the degree of intergranular weakening is smaller.At the same time,not only MX in the grain interiors but also the solid-solutioned C and W in the matrix decrease in modified T23 steel,leading to the decline of intragranular strengthening.In addition,small grain size is beneficial to the improvement of the reheat cracking susceptibility of modified T23 steel.The decreased number of M23C6 at grain boundaries helps to retard the formation and propagation of reheat cracks because of decreased denuded zones.
其他文献
以中药渣(TCMR)为原料,采用真空热解方式制备中药渣生物炭,通过扫描电镜(SEM)、比表面积及孔径分析仪、傅里叶红外光谱(FTIR)等表征手段进行分析.中药渣生物炭的BET比表面积为808.6 m2/g,平均孔径是0.97 nm,表面有大量活性官能团.静态吸附实验结果表明,pH=7时中药渣生物炭对活性蓝19的吸附量最高;中药渣生物炭对活性蓝19的吸附过程符合准二级动力学模型(R2>0.994)和Langmuir吸附等温线(R2>0.996),最大吸附量达到85.47 mg/g.热力学分析表明该吸附过程是
At present,the continuous accumulation of the flue gas desulfurization (FGD) gypsum in steel plants leads to the serious environmental issues and resource waste.To achieve green and sustainable development for the steel industry,it is significant to impro
The stability of the Fe23Zr6 phase in Fe-Zr system was studied,and the partial Fe-Zr phase diagram was revised by means of X-ray diffraction,electron probe microanalysis and differential thermal analysis methods.On the basis of the experi-mental results i
基于2019年台儿庄城区饮用水水源地水质监测数据,探讨了水源地水质的季节变化特征,采用内梅罗综合指数法对其进行了评价.结果显示:与《地下水质量标准》(GB/T 14848—2017)指标限值相比,仅张庄水源地水质中总硬度超标,其余指标符合要求;张庄水源地水质指标的质量浓度大于小龚庄水源地;张庄水源地水质处于良好级别,小龚庄水源地水质处于优级别.
During multi-jet cooling,the complex hydrodynamic characteristics caused by the interaction between jets will affect the heat transfer of the plate.To further clarify the heat transfer characteristics in different flow regions,the double-jet cooling exper
The effect of La on inclusions and fracture toughness of 40CrNi2Si2MoVA steel was investigated via the optical microscope,scanning electron microscope,image software and electronic universal testing machine.The results reveal that the inclusions in steel
With significant emphasis on reducing the turbulence in the bath and the need for effective distribution of metal along the roller length in twin-roll casting,a novel submerged entry nozzle (SEN) configuration with two “gap regions” was provided.The “gap
在5G万物互联时代,面对复杂的网络结构和海量的网络数据,网络数据安全形势愈发严峻,亟须完善网络安全保障能力.以中国移动集团对数据安全的重点工作要求为指导,结合本地业务系统的实际工作,并基于大数据分析和机器学习等前沿技术,分别从敏感数据资产的梳理、识别和分类分级,敏感数据的端口、流量监测和风险评估,操作日志的审计等方面进行了数据安全的研究,探讨了数据安全管控的现状和管理手段,分析了企业面临的安全风险,提出了有效的解决方案.
The microstructures and tension properties of Fe50Mn20Cr20Ni10 medium entropy alloy (MEA) were investigated,which was produced by vacuum induction melting and subsequently was homogenized at 1200 ℃ for 6 h.Microstructure characterization shows the single-
VxFeCoNiCu high entropy alloy matrix composites reinforced by in situ TiC particles (10 vol.％),i.e.,VxFeCoNiCu/TiC composites,were fabricated from V-Fe-Co-Ni-Cu-Ti-C system using vacuum inductive melting method.With the content of vanadium increasing,the