The Huize Pb-Zn deposits of Yunnan Province, located in the south-central part of the Sichuan-Yunnan-Guizhou (SYG) Pb-Zn multimetal mineralization district (MMD), are strictly controlled by fault zones. The sources of ore-forming fluid in the deposits have been debated for a long time. Calcite, a gangue mineral, has uniform C and O isotopes. The δ~13C_PDB and δ~18O_SMOW values vary respectively from -2.1×10~-3 to -3.5×10~-3 (mean -2.8×10~-3) and 16.7×10~-3-18.6×10~-3 (mean 17.7×10~-3). No obvious difference can be found in C and O isotopes among occurrences and elevations and even ore-bodies. Types of inclusions include those of pure liquid (L), liquid-rich gas-liquid (L+V), and three-phase ones containing a daughter mineral (S+L+V) and immiscible CO_2 with three-phases (V_CO_2+L_CO_2+L_H_2O). Their homogenization temperatures vary from 110 to 400 ℃, and two peaks are shown. (~87Sr/~86Sr)_0 ratios of calcite in the deposits are higher than those in the mantle and Emeishan basalts, and slightly higher than those in the Baizuo Formation, which the Huize lead-zinc deposits are found in. All of the (~87Sr/~86Sr)_0 are low relative to those in the basement rocks. Fractionation of Sr isotope did not occur in the ore-forming fluid during the precipitation of minerals. The results indicate that the ore-forming fluid is homogeneous and derived from the mixing of different fluids. Gas-liquid inclusions can be separated into two groups in 300-400 ℃ with a salinity of 5 %-6 % and 12 %-16 % NaCl respectively. However, the salinities of inclusions vary from 7 % to 23 % NaCl in 100-300 ℃, especially in 150-250 ℃. The formation pressures of faulted zones are (50-320)×105 Pa. The estimated pressures of the overlying rocks on the ore bodies are 574×105-640×105 Pa. The pressures of ore-forming processes would be 145×105 to 754×105 Pa. Therefore, pressure sharply reduced and boiling occurred when the ore-forming fluid flew into the fault zones. As a result, the ore-forming fluid was highly concentrated, and metallic minerals began to precipitate from the fluid on a great scale. The high-grade lead-zinc deposits were formed when the fluid was under saturation or over-saturation conditions. The Huize Pb-Zn deposits of Yunnan Province, located in the south-central part of the Sichuan-Yunnan-Guizhou (SYG) Pb-Zn multimetal mineralization district (MMD), are strictly controlled by fault zones. The sources of ore-forming In the deposits have been debated for a long time. Calcite, a gangue mineral, has uniform C and O isotopes. The δ ~ 13C_PDB and δ ~ 18O_SMOW values ​​vary vary from -2.1 × 10 ~ -3 to -3.5 × 10 ~ -3 (mean -2.8 × 10 -3) and 16.7 × 10 -3 -3.6 × 10 -3 (mean 17.7 × 10 -3). No obvious difference can be found in C and O isotopes among occurrences and elevations and even ore-bodies. Types of inclusions include those of pure liquid (L), liquid-rich gas-liquid (L + V), and three-phase ones containing a daughter mineral (S + L + V) and immiscible CO_2 with ~ three-phases (V_CO_2 + L_CO_2 + L_H_2O). Their homogenization temperatures vary from 110 to 400 ° C, and two peaks are shown (~ 87Sr / ~ 86Sr) _0 ratios of calcite in the deposits are higher than those in the mantle and Emeishan bas alts, and slightly higher than those in the Baizuo Formation, which the Huize lead-zinc deposits are found in. All of the (~ 87Sr / ~ 86Sr) _0 are low relative to those in the basement rocks. Fractionation of Sr isotope did not occur in the ore-forming fluid during the precipitation of minerals. The results indicate that the ore-forming fluid is homogeneous and derived from the mixing of different fluids. Gas-liquid inclusions can be separated into two groups in 300-400 ° C with a Salinities of 5% -6% and 12% -16% NaCl respectively. However, the salinities of inclusions vary from 7% to 23% NaCl at 100-300 ° C, especially at 150-250 ° C. The formation pressures of faulted zones are (50-320) × 105 Pa. The estimated pressures of the overlying rocks on the ore bodies are 574 × 105-640 × 105 Pa. The pressures of ore-forming processes would be 145 × 105 to 754 × 105 Pa. Thus, pressure sharply reduced and boiling occurred when the ore-forming fluid flew into the fault zones -forming fluid was highly concentrated, and metallic minerals began to precipitate from the fluid on a great scale. The high-grade lead-zinc deposits were formed when the fluid was under saturation or over-saturation conditions.