The Further Discussion of Distribution and Characters of Grey Potential Degrees

来源 :第28届全国灰色系统学术会议 | 被引量 : 0次 | 上传用户:zxblovezxh
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
  Grey number has become a very important and useful tool to describe the pay-off matrix of game due to the inevitable defect of information and the limited rationality of human.The conception system of Grey Potential Degrees,including Grey Superiority Potential Degree,Grey Inferior Potential Degree and Grey Total Potential Degree of two grey numbers is built up in exiting research.This paper is to further discuss the distribution,the characters and the changing of these Grey Potential Degrees.Distribution of Grey Potential Degree is discussed in the paper and Grey Superiority Degree is divided into three areas,Absolutely Superiority,Relative Superiority and No Superiority.And Grey Inferior Potential Degree is divided into three parts,Absolutely Inferiority,Relative Inferiority and No Inferiority.It is found that any two grey numbers could be in some special situation of No Superiority to Each other,No Inferiority to Each other,Unit Superiority Potential.When they are same grey numbers,all Grey Potential Degrees are in value of zero.Grey Potential Degrees of Grey Numbers can be in mutual influence.They are connected with the length of grey numbers.According to the dimension of position and the dimension of length of grey umbers,the changing and tendency of three kinds of Grey Potential Degrees are stimulated,accounted and figured in paper.The growing tendencies of Grey Potential Degrees are presented when one grey number moves from left side to right side of the other grey number.Closer the lengths of two grey numbers are,nearer the Grey Superiority Potential Degree and Grey Inferior Potential Degree.
其他文献
  脉纹、渗透,和气体等是铸铁及铸钢厂一直试图控制的常见铸造缺陷.这些缺陷导致过高的废品率从而迫使铸造厂使用昂贵的涂料.涂料同时需要时间得以干燥从而降低了生产效率.
  粘土湿型砂造型是中小铸铁件生产中采用的主要工艺,其主要材料为石英砂、膨润土和煤粉。而在粘土砂造型、砂处理、旧砂再生过程中要产生大量粉尘;经试验经过分析,这些粉尘中
  树脂覆膜砂作为铸造技术的一种主要造型材料已发展多年,但因其基本技术原理是使用酚醛树脂添加潜伏性固化剂乌洛托品,在制芯过程中会排放大量的恶臭气体影响环境和工人身体
会议
  本文介绍目前铸造旧砂再生的必要性和紧迫性,以及铸造旧砂再生(再利用)现状。铸造旧砂类别及再生方法,再生砂性能要求,湿型砂旧砂热法再生技术及应用效果。
  由于目前铸件内部通道日趋复杂和弯曲,使生产者很难检测潜在的通道堵塞。如因断芯导致的铸造缺陷,砂芯残余等,都可能存在于铸件内部通道中。对此,法肯提供了光学检测和气体检
  在相同的设备上对不同需求量的多种产品的生产过程进行建模计算,是一种实现规划和优化的工作的全新的方式。在设备上或生产过程中微小的调整可以对整个铸造厂的产能造成影
  真空离心熔模铸造技术的研发主要意在用于高负荷的泵件叶轮.通过这项技术,可以有效地减少叶轮的尺寸和重量.其优势在于可将钢的叶轮的壁厚降低至0.8-1.5毫米,叶轮的负载能
  本文依据大连誉洋工业智能有限公司在中国重汽杭州发动机有限公司柴油机缸体的机器人自动化打磨项目的实施中获得的经验,对影响机器人打磨质量和效率的各种因素进行分析,总
  汽车行业的快速发展,带动了汽车铸造业的发展,对汽车铸件的质量提出了更高的要求。目前,在铸造工厂中,机器人已经被广泛用到制芯、造型、清理及熔化等工部中,机器人的应用将是
  本文通过介绍D12发动机缸体毛坯开发过程中遇到的气孔、水套内腔粘砂、结疤等缺陷的解决方法,提出细化对砂芯排气、制芯过程排气等细节的研究和优化的重要性。