Design of the Singapore Sports Hub roof with high strength niobium steel

来源 :第五届宝钢学术年会 | 被引量 : 0次 | 上传用户:qtedu
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
  Singapore National Stadium roof structure is a highly efficient dome spanning 310 m with a rise of 85 m from the ground level.When complete,the fixed roof will be the largest clear span dome roof in the world and supports a symmetrical movable roof in 2 halves.The fixed roof structure is formed by a series of steel arch trusses that are supported by a post - tensioned concrete ring beam.The trusses are constructed from CHS elements and form a highly efficient braced dome structure.This paper considers the potential savings in material use that could have been made if higher strength,high elongation steel had been economically viable and could have been competitively tendered.It is shown that it could be possible to make a significant saving on element steelwork if either hot finished niobium grain refined S500 0r S690 can be adopted for similar projects in the future.
其他文献
预矫直机上线后TMCP钢板的开冷温度较以前降低,根据现场的检测结果发现,预矫本体并非导致终轧至开冷温度降低的主要原因.对预矫上线前后钢板的速度走势进行了总结、分析,建立
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
  The investigation on toxicity of stainless steel is reviewed.Many countries established their law to guarantee food security of stainless steel,Development
会议
介绍了热处理对06Ni9DR低温压力容器钢板的组织的影响和钢板最终状态的力学性能,莱钢采用QLT(淬火+两相区淬火+回火)热处理试制的钢板具有良好的强韧性匹配,具有良好的低温冲击
会议
  Steel grade B445JIM was found to have more sticking possibility in hot rolling than that of grade SUS430.Oxide scale is a key factor affecting the sticking
会议
采用增重法研究了奥氏体耐热不锈钢S30908、S31008和S30815在900℃的氧化速率,并借助于扫描电镜和XRD分析了氧化膜表面和横截面的形貌。结果表明:S30908和S31008的氧化速率接
针对中厚板热轧时出现的边裂缺陷,研究了其形成原因及控制方法。结果表明,钢中[Al]、[N]控制不当,生成[AlN]析出造成晶界脆性,二冷水量冷却不均,结晶器振动偏摆量过大是边裂产
概述介绍了原油船货油舱(Cargo oil tanks)的腐蚀情况和主要防护措施,并对货油舱耐蚀钢发展历史、技术应用和国内外产品研制情况进行了阐述.结合原油船货油舱的腐蚀特点和国
会议
金弹子、老鸦柿均为近年来较为热门的盆景树种,二者都具有根干虬曲多姿,果实鲜艳,观赏期长等特点,而且同为柿科柿属植物,形态也有诸多相似之处,还都有山柿子、丁香柿等别名.
期刊
含高合合的板坯,在切割工序中比较容易产生热裂纹缺陷,而这种裂纹缺陷在后续的板坯加热、轧制工序中会遗留下来甚至进一步扩展,很可能造成用户所需要的产品尺寸得不到保证,且